line is fast enough to be a daily machine Size first, since that is the constraint. A VHS head drum is 62 mm across and spins at 1500 rpm with its own direct drive motor and a very good bearing, so it is usable -- but as a spindle, not as a medium: its own heads are for tape, and the video tape transport is exactly the complexity we do not want. Strip the heads, glue an annulus of floppy media onto the upper drum, and put two fixed heads (cassette or stripe heads) at the rim: at 62 mm one cell is 3.0 mm of circumference, so the heads can be crude and the read-modify-write pair sits 3 mm apart with no machining. A dead 2.5 inch hard disk spindle is cheaper and spins five times faster, with a floppy head (100 um track) parked open loop over a disc of floppy media. What that costs in practice is now measured rather than guessed. The 8 bit calculator session is 166348 steps: 65311 forward pointer moves and 65278 backward ones. On a 25 rev/s drum a forward move waits one cell (625 us) but a backward move waits 64-k cells, about 38 ms for the usual k, so a session is 41 minutes and the flagship tape 23 minutes. hello is 0.3 seconds. A magnetostrictive delay line has a full revolution of 0.5 ms instead of 40 ms: the same session is 32 s and the flagship 18 s, because its backward move waits at most one revolution. So the drum is an exhibit machine, and the delay line is the only mechanical memory that can be used interactively -- both because of the same property, how long one lap takes. Also recorded: what the drum needs besides the mechanism -- an index pulse, a 64x clock resynchronised to it every revolution, a plain FM channel (one clock transition per cell plus a data transition for a 1) read with a windowed latch, and the second head for read-modify-write.
ROT-8 硬件:这个目录里有什么
docs/hardware.md 的落地部分。三样东西都跑通了(Icarus Verilog 14.0):
| 文件 | 是什么 | 状态 |
|---|---|---|
rot8.v |
机器的 RTL:8 条指令、3 bit 操作码、6 位 dp 的 64 格环、循环栈式括号跳转 |
✅ 与软件逐字节一致 |
tb_rot8.v |
testbench:$readmemh 一张镜像,跑到停机,按 tape_run 的格式打印 OUT 流和步数 |
✅ |
(工具)r8forge_tape_pack |
文本纸带 → 3 bit 打包镜像 + --hex($readmemh 用) |
✅ 在 tests/ 里 |
实测:RTL 与软件完全一致
8 位 / 64 格,tape_run --loop-stack --retest(板子实际采用的口径)对标 vvp:
| 纸带 | 指令数 | 步数 | OUT 个数 | 结果 |
|---|---|---|---|---|
-+. 微测试 |
3 | 3 | 1 | ✅ 打出 128 |
hello |
577 | 417 | 10 | ✅ |
term(输入 lhi) |
16 414 | 17 643 | 11 | ✅ |
calc(输入 12 34 + .) |
51 378 | 166 741 | 19 | ✅ 打出 > 12 34 + . / 046 / > |
全家桶 asm/test.r8asm |
43 676 | 100 142 | 93 | ✅ |
自动化:ctest -R rtl_sim(在 8 位 / 64 格的构建里真跑,其它几何打印 SKIP)。
tests/rtl_sim.cmake 就是那一轮:汇编 → 打包 → 软件跑 → iverilog 编 → vvp 跑 → 比对
OUT 流和步数。
自己跑一遍
# 8 位 / 64 格的构建(RTL 就是这台机器)
cmake -S . -B build8 -DR8FORGE_CELL_SIZE=8 -DR8FORGE_MEMORY_CELLS=64
cmake --build build8 --config Release
# 1) 汇编 + 打包 + 出 hex
build8/Release/r8forge examples/hello.r8asm > hello.rot8
build8/Release/r8forge_tape_pack hello.rot8 -o hello.r8t --hex hello.hex --verify
# 2) 软件侧金标准(注意两个开关)
build8/Release/r8forge_tape_run hello.r8t --loop-stack --retest
# 3) RTL
iverilog -g2012 -o rot8_tb.vvp hardware/rot8.v hardware/tb_rot8.v
vvp rot8_tb.vvp +HEX=hello.hex +LEN=577
带输入的程序(calc、term):把输入写成一个文件(不要换行),用 +INFILE= 喂;
文件读完之后机器读到 0(和解释器的 EOF 语义一致):
printf '12 34 + .' > calc_in.txt
vvp rot8_tb.vvp +HEX=calc8.hex +LEN=51378 +INFILE=calc_in.txt
build8/Release/r8forge_tape_run calc8.r8t --loop-stack --retest -i '12 34 + .'
两个坑(都踩过)
+HEX=/+INFILE=的路径必须是纯 ASCII。Icarus 把 plusarg 原样传下去,路径里有 中文(这个仓库就在…/文档/…下)时$readmemh收到的是乱码,内存静默留空,机器 就把一整条"全是 0 号操作码"的纸带跑完、什么都不打。要么cd进 hex 所在目录用相对 路径(tests/rtl_sim.cmake就是这么做的),要么把文件拷到 ASCII 路径。in_ready不能加!in_valid的限定。第一版写成in_ready = … && !in_valid, 于是生产者永远看不到"接受"的边沿、握手死锁 —— 只有hello这种不读输入的纸带能跑。
RTL 里几个"故意这么写"的地方
- 程序存储器读 16 位窗口(
prog_addr0/prog_addr1两次字节读):3 bit 指令会跨字节, 取指必须看到相邻两个字节。真实板子上这对应"16 位宽 ROM"、"两片 ROM"或一个移位寄存器。 - 循环栈的进出账跟跳法绑定:跳回
['本身(retest)时]必须弹栈(['重跑会 再压一次);跳回['之后一格时要留栈到循环退出。RTL 只实现前者(契约口径), 软件侧--loop-stack --retest与它对应;r8forge_tape_pack_test盯着四种组合输出一致。 biz的前向跳过是独立状态(S_SCAN):每拍读一条、不算步数,跳到配对的]之后 再多走一格。,阻塞:in_ready拉高、所有寄存器保持到in_valid;读到 0 必须显式给 (in_valid+in_data=0)。- 停机:
ip >= prog_len→halted,并且这一拍不再执行(第一版漏了判断,会从纸带外 多取一条、步数多 1)。
还没做的
- 上板(M1):RTL 已经能跑,缺的是引脚约束、时钟、串口和面板。
- ROM 烧写格式:28C256 / 39SF010 吃裸二进制 ——
tape pack -o x.bin去掉 16 字节 trailer 即可(--hex那份是给仿真用的)。 - UART / 前面板 / 单步:RTL 已经留了
run/step/ip/dp/steps/halted。